單向節流閥，MK/MG15
單向節流閥 MK/MG15 產品介紹
中文介紹
單向節流閥 MK/MG15 是一種廣泛應用于液壓系統中的流量控制元件。它主要由閥體、調節套、閥芯和彈簧等部件組成，通過調節節流口的截面積來控制液壓油的流量。
工作原理：
-
當液壓油從閥的節流方向流入時，壓力油和彈簧將閥芯壓在閥座上，形成節流口。液壓油通過閥體和調節套之間的節流口流動，用戶可以通過旋轉調節套來無級調節節流口的過流截面，從而實現對流量的精確控制。
-
在相反方向，液壓油作用于閥芯的錐面上，將閥口打開，使液壓油無節流地通過單向閥。同時，部分液壓油通過環形槽流動，能夠清除節流口上的沉積物，起到自我清潔的作用。
性能特點：
-
適用范圍廣：通徑為15mm，最大工作壓力可達315bar，最大流量可達400L/min，能夠滿足多種液壓系統的需求。
-
調節靈活：通過旋轉調節套，用戶可以方便地調節節流口的大小，實現對流量的無級調節。
-
自我清潔功能：在單向閥工作時，部分液壓油通過環形槽流動，能夠清除節流口上的沉積物，減少堵塞的風險，提高閥的使用壽命。
應用場景： MK/MG15 單向節流閥適用于多種液壓系統，如工程機械、工業自動化設備、液壓傳動裝置等。它可以用于控制液壓缸或液壓馬達的速度，實現平穩、精確的運動控制。
英文 Introduction
The MK/MG15 check throttle valve is a widely used flow control element in hydraulic systems. It mainly consists of a valve body, adjusting sleeve, valve core, and spring, and controls the flow of hydraulic oil by adjusting the cross-sectional area of the throttle port.
Working Principle:
-
When hydraulic oil flows into the valve in the throttling direction, the pressure oil and spring press the valve core against the valve seat to form a throttle port. The hydraulic oil flows through the throttle port between the valve body and the adjusting sleeve. Users can rotate the adjusting sleeve to adjust the cross-sectional area of the throttle port steplessly, thereby achieving precise flow control.
-
In the opposite direction, the hydraulic oil acts on the conical surface of the valve core, opening the valve port and allowing the hydraulic oil to flow through the check valve without throttling. At the same time, part of the hydraulic oil flows through the annular groove, which can clean the throttle port and remove deposits.
Performance Features:
-
Wide Application Range: With a port diameter of 15mm, it can handle a maximum working pressure of 315bar and a maximum flow rate of 400L/min, meeting the needs of various hydraulic systems.
-
Flexible Adjustment: Users can conveniently adjust the size of the throttle port by rotating the adjusting sleeve to achieve stepless flow control.
-
Self-cleaning Function: When the check valve is working, part of the hydraulic oil flows through the annular groove, which can clean the throttle port and reduce the risk of blockage, thereby extending the service life of the valve.
Application Scenarios: The MK/MG15 check throttle valve is suitable for a variety of hydraulic systems, such as construction machinery, industrial automation equipment, and hydraulic transmission devices. It can be used to control the speed of hydraulic cylinders or hydraulic motors, achieving smooth and precise motion control.
簡單介紹
MK/MG15 單向節流閥這時由于有部分油液可在環形縫隙中流動，可以清除節流口上的沉積物。MG型(節流閥)
MK/MG15 單向節流閥
的詳細介紹
MK/MG15 單向節流閥
通徑（NG）8至30 壓力至31.5Mpa 流量至400L/min MG6.MG8.MG10.MG15.MG20.MG30
|
MK型單向節流閥從通徑6至通徑30共7個規格。
當壓力油從錐閥背面流入時，它作為節流閥使用，
若從相反方向 流入時，它作為單向閥使用，這時由于
有部分油液可在環形縫隙中流動，可以清除節流口上
的沉積物。MG型(節流閥)
該閥可以雙向節流。油通過旁 孔(3)流向閥體(2)和可
調節套向(1)之間形成的節流口(4)。轉動套筒(1)能夠
改變節流斷面。MK6.MK8.MK10.MK15.MK20.MK30節流閥
|
|
歡迎光臨上海雙旭電子有限公司 接近開關 漆膜測厚儀 照度計 超聲波測厚儀 |
