電容器BSMJ0.4-12-3
產品概述
BSMJ0.4-12-3是一款三相自愈式低壓并聯電力電容器，采用金屬化聚丙烯薄膜作為介質材料，專為380V工頻交流電力系統設計。該產品通過先進的制造工藝實現了緊湊化設計，體積和重量?jī)H為傳統產品的1/4至1/5，特別適合空間受限的配電系統安裝。產品內置放電電阻和過壓力保護裝置，能在斷電后3分鐘內將殘余電壓降至安全范圍，同時具備故障自動隔離功能，有效提升運行安全性。采用半固體微晶蠟浸漬技術，確保全生命周期內無滲漏風險，符合環保要求。典型應用場景包括工業廠房、商業建筑等需要功率因數校正的低壓配電網絡。1212
The BSMJ0.4-12-3 is a three-phase self-healing low-voltage shunt power capacitor utilizing metallized polypropylene film dielectric. Designed for 380V/50Hz AC power systems, it features a compact structure with volume and weight reduced to 20%-25% of conventional models. The integrated discharge resistor ensures residual voltage drops below 50V within 3 minutes after power-off, while the built-in pressure-sensitive protection device provides fault isolation capability. Environmentally friendly microcrystalline wax impregnation technology eliminates leakage risks throughout service life. Typical applications include power factor correction in industrial plants and commercial buildings.416
技術特點
該電容器具備優異的自愈性能，當介質局部因過電壓發生擊穿時能瞬間恢復絕緣特性，使產品可靠性顯著提升。損耗角正切值低于0.1%，自身能耗極低，工作溫升小，延長了使用壽命。電氣參數方面，額定電壓400V，容量12kvar，容量允差范圍+10%，極間耐壓達2.15倍額定電壓（10秒測試）。產品適用于海拔2000米以下環境，工作溫度范圍-25℃至+50℃，濕度不超過85%。獨特的金屬化膜邊加厚工藝增強了抗涌流能力，允許在1.3倍額定電流下持續運行。5822
Key technical features include outstanding self-recovery capability that automatically repairs dielectric breakdown spots, with tanδ loss below 0.1% for minimized energy consumption. Electrical specifications show 400V rated voltage, 12kvar capacity (+10% tolerance), and 2.15×Un inter-electrode withstand voltage (10s test). Operational environment covers altitudes up to 2000m, ambient temperature -25℃ to +50℃, and ≤85% humidity. The reinforced metallized edge technology improves surge current resistance, allowing continuous operation at 130% rated current.3725
結構設計
產品采用矩形金屬外殼結構，標準三相三角形接法（△），內部元件經過200倍額定電流的老練處理以提高穩定性。創新性的真空灌裝工藝確保浸漬劑均勻分布，配合特殊密封設計防止氧化。安裝時需保持豎直姿態，多臺并聯時間距需大于30mm以保證散熱效果，夏季高溫環境建議增加強制通風措施。連接導線推薦采用截面積不小于4mm²的多股軟銅線，端子螺栓扭矩應達到3N·m以確保接觸可靠性。外殼防護等級滿足常規室內安裝要求，避免陽光直射和雨雪侵蝕。61527
Structurally designed with rectangular metal enclosure and delta connection (△), the capacitor undergoes 200×In aging process for enhanced stability. Vacuum impregnation technology ensures uniform dielectric distribution, with special sealing against oxidation. Installation requires vertical orientation with ≥30mm clearance between multiple units. Recommended connection uses ≥4mm² stranded copper wires with terminal torque of 3N·m. The enclosure protection level suits standard indoor environments, avoiding direct sunlight and precipitation exposure.91728
應用價值
在電力系統中使用時，能有效提高功率因數至0.95以上，降低線路無功損耗15%-30%，改善電壓波動問題。相較于傳統電容器，年運行損耗減少約40%，配合自動投切裝置可實現智能化節能管理。典型投資回報周期為8-12個月，長期運行可減輕變壓器負荷，釋放10%-15%的供電潛能。維護方面僅需定期檢查外殼是否變形、端子是否松動等基礎項目，正常使用條件下設計壽命超過10萬小時。1013[
簡單介紹
BSMJ0.4-12-3 電容器3、的自愈性能： 過電壓所造成的介質局部擊穿能迅速自愈，恢復正 常工作，使可靠性大為提高。4、安全性：內裝自放電電阻和保險裝置。 內裝放電電阻能使電容器上所 帶的電能自動泄放掉
BSMJ0.4-12-3 電容器
的詳細介紹
|
